Re: Is Roger's throttling Netflix now?
In Netflix, you can also go into your profile settings on the web site and force the highest quality streaming all the time rather than have it throttled back if that's what you want. Even at HD...
View ArticleClik here to view.
Re: Is Roger's throttling Netflix now?
Right, but even on HD settings, unless you have the right supported device... are just going through the web browser, etc, you are going to be at the lower rate. Unless you have a supported device....
View ArticleClik here to view.
Re: Sending internet usage stats via email
I like that if you have a rogers cellphone, you can check the home internet usage, via the APP now too
View ArticleRe: Is Roger's throttling Netflix now?
Well, I only use a browser on my computers for watching Netflix and I always get HD once I set my profile settings to that all the time. It doesn't bother to negotiate up and down, etc when you do...
View ArticleWPS Button on Rogers Advanced Wifi Modem?
I am wondering where the WPS button is on the modem because I got a range extender to connect to it and I have no idea where it is.
View ArticleRe: WPS Button on Rogers Advanced Wifi Modem?
The WPS button is on the front of the CGN3, under the LEDs. From the manual: Press this button to begin the WiFi Protected Setup (WPS) Push-Button Configuration (PBC) procedure. Press the PBC button...
View ArticleRe: WPS Button on Rogers Advanced Wifi Modem?
I do agree with Datalink.WPS in general is a security risk.. and there have been many exploits based around it being enabled on different devices in the past.You would be best to connecct it via OTHER...
View ArticleClik here to view.
Re: CIsco DPC3825 TERRIBLE; How do I work around it?
I've got exactly the same problem.Wireless signal drops and even when I put my modem and laptop on the table few centimeters apart from each other the issue was still there.I tried:1. replacing the...
View ArticleRe: CIsco DPC3825 TERRIBLE; How do I work around it?
Personally I'm all for #11. Great idea. Realistically, the best thing you could do is put the 3825 in bridge mode and use your own router for everything else, wired and wireless. You will be much...
View ArticleRe: CIsco DPC3825 TERRIBLE; How do I work around it?
Hmm. At min.. getting a 3rd party router.. even a cheaper one... and putting the unit into bridge mode.. SHOULD fix most wireless issues, especially if you are even right near the modem. It does sound...
View ArticleRe: WPS Button on Rogers Advanced Wifi Modem?
I haven't used the CGN3 in gateway mode for a while but as I recall it also has the ability to do IP reservation based on MAC addresses. That way you can avoid having to create a static IP address...
View ArticleClik here to view.
Re: WPS Button on Rogers Advanced Wifi Modem?
Yeah, it does have a reservation.I found, milage may varry with reservation, at least last time i used it (was on a much older router).One device.. it NEVER worked on.. was the right MAC address.. but...
View ArticleAccessing Cisco DPC3825 IGMP Settings
I used to be able to access my router by going to File Explorer and then Network, but now it doesn't show up, only the other devices (e.g. printer, other computers that are online, etc.) How can I...
View ArticleRe: Extremely slow download speeds & Very LiMITED MODEM RANGE
If you read through some of the posts in the forum you will see that all models of the combo modem / routers have been a source of frustration due to their poor wifi performance. The easiest way to...
View ArticleCGN3 - Windows fast - Linux slow
I've had a CGN2 for over a year. I also use Linux operating system exclusively. Have done many speedtests with it over the last year and I have always had good results ... about 40Mbps down and 10 up...
View ArticleRe: Accessing Cisco DPC3825 IGMP Settings
I wonder if the router address isn't being properly used for some strange reason. Try this. Open a command prompt and type in: ipconfig When the data comes up look for the Default Gateway address....
View ArticleRe: CGN3 - Windows fast - Linux slow
hmm. Looks like there might be more than one issue here. Can we start by having a look at your cable data, just to see if there is any issue with it. Here's a link to my CGN3 cable data as an...
View ArticleClik here to view.
Re: CGN3 - Windows fast - Linux slow
Thats interesting Mr Datalink. I did read your edit. I remember seeing something about that while scouring these forums before posting. You may have hit the nail on the head. I did un-bridge and get...
View ArticleClik here to view.
Re: CGN3 - Windows fast - Linux slow
Signal shouldnt generally be the problem, at least in this case specifically.. though, it looks like your number are a bit off. The signal strength, you want as CLOSE as you can, to 0. That you are...
View ArticleClik here to view.
Re: Wi-Fi Channels
5ghz vs 2.4 getting different range, IS normal.5ghz, while it usually will NOT run into interfearance compared to 2.4.. the higher the freqency, the shorter the distance it will go.You would be amazed...
View Article